Today, I completed a thorough electrical inspection for a home in Cape Coral, FL. I tested the breaker panel, checked all wiring connections, and inspected outlets for proper grounding. I also verified the functionality of GFCI outlets in wet areas, ensuring the system complied with current NEC standards.

At a business in Cape Coral, FL, I installed eight 6-inch Halo recessed LED lights in the main office area. I measured and cut ceiling holes, ran new wiring to the junction box, and connected the lights to a dimmer switch for adjustable brightness. The installation improved lighting coverage while maintaining a clean and modern look.

I upgraded an old electrical panel to a 200-amp Square D panel for a home needing more power. I replaced the outdated panel, installed new circuit breakers, and ensured all connections were up to code. After testing the panel and checking each circuit, the system was functioning properly, and the home’s electrical capacity is now up to modern standards.

For this job, I installed multiple lighting fixtures in a home. I began by turning off the power and removing the old fixtures. I then mounted the new LED fixtures and connected the wiring to the existing junction boxes. I used wire nuts and secured all connections properly before testing each light for proper function. The fixtures are now providing bright, efficient lighting, and all connections meet safety standards. After installation, I cleaned up the area and ensured the homeowner was satisfied with the results.

I responded to a commercial call for an emergency electrician. Upon arrival, I found that a main breaker had tripped, cutting off power to a section of the building. I reset the breaker and inspected the distribution panel for any underlying issues. I discovered that the overloaded circuits were causing the issue, so I advised the facility on necessary electrical upgrades to prevent future outages. After ensuring the breaker and wiring were functioning correctly, power was restored, and operations resumed.

I installed a whole home surge protection system to safeguard a client’s electrical devices. I selected the Eaton CHSPT2ULTRA surge protector and mounted it directly on the main electrical panel. After connecting the device to the panel’s bus bars, I tested it with a surge simulator to verify proper operation. This installation now provides the home with protection against power surges, reducing the risk of damage to sensitive electronics.

I repaired a malfunctioning GE dishwasher that wasn’t starting. After inspecting the unit, I discovered a faulty thermal fuse. I replaced the blown fuse with a new GE OEM part and checked the wiring connections for any signs of wear. After reassembling the unit, I ran a complete cycle to confirm the repair was successful, ensuring the dishwasher was fully operational before leaving the site.

I completed electrical repairs in a home where several outlets had lost power. After troubleshooting with a Fluke 117 multimeter, I identified a faulty GFCI outlet in the kitchen. I replaced the old outlet with a new Leviton GFCI and restored power to the affected circuits. I then tested all related outlets to ensure they were functioning properly and provided the homeowner with tips on preventing future issues.

Repaired a Bosch SHE3AR75UC dishwasher today. Diagnosed faulty circulation pump using Fluke 117 multimeter. Replaced pump with Bosch 00239144 circulation pump assembly. Cleared clogged drain hose using Ridgid K-3 drain auger. Replaced worn door gasket with Bosch 00432490 seal. Cleaned spray arms with CLR descaling solution. Checked and tightened all hose connections. Tested water inlet valve function. Verified proper drainage and cycle operation. Used Bosch Service Assistant software for final diagnostic check. Completed repair in 2.5 hours, restoring optimal dishwasher performance.

Today, I installed electrical outlets in a new game room. Assessed the layout and determined optimal outlet placement. Ran 12-gauge Romex wiring from the main panel to the designated locations. Installed Leviton tamper-resistant outlets and ensured all connections were secure and up to code. Used a Klein voltage tester to confirm proper voltage and functionality. The new outlets provide ample power for gaming equipment and enhance the room's usability. Advised the homeowner on safe electrical practices and the benefits of regular maintenance.

Rewired kitchen electrical circuits to meet current NEC code. Removed old cloth-jacketed knob-and-tube wiring and outdated fuse panel. Installed new 20-circuit main lug load center with AFCI/GFCI breakers. Ran NM-B romex in EMT conduit for new counter, lighting and appliance circuits using proper box fill calculations. GFCI protected all countertop receptacles. Connected new dedicated NEMA 14-50 outlet for electric range.

Installed new 6-inch IC-rated LED recessed lighting in living room per NEC standards. Cut precise openings in drywall using a RotoZip tool. Ran new 14/2 NM-B romex cable from lighting circuit. Wired fixtures to junction boxes using proper connections and cable clamps. Connected grounds to metal cans. Tested lights on dimmer switch before securing trims.

I undertook a comprehensive rewiring project for a home experiencing numerous electrical issues. This involved replacing outdated wiring with new, code-compliant Romex NM-B cable throughout the residence. Key installations included GFCI outlets in wet areas, model Leviton 20 AMP, and AFCI breakers in the main panel, model Square D Homeline, to enhance safety and functionality. The project was meticulously executed to address and resolve all existing electrical problems.

I completed the installation of six Philips Hue Ambiance recessed LED lights in a residential kitchen. This included planning the layout for even illumination, cutting precise openings in the ceiling, wiring each fixture to the home's electrical system, and securing the lights into place. I finished by connecting them to a Philips Hue Bridge for smart control, enhancing the kitchen's ambiance and functionality.

Responded to a client's concern in Cape Coral, FL, experiencing flickering lights and a burning smell. After a thorough inspection, determined the need for a home rewiring due to old, faulty wiring. Completed task should take about three days total. Currently helping customer make preparations for the rewire, to ensure it goes as smoothly as possible.

Completed a whole-house surge protection installation, in Cape Coral, FL. This will safeguard the residence from electrical surges. I did an assessment to determine best placement of surge protectors. Installed devices at key points in the electrical system, providing comprehensive coverage. Tested the system to ensure effective protection against voltage spikes. The installation enhances the home's electrical resilience, safeguarding sensitive electronics from potential damage.

Addressed a residential electrical panel issue in Cape Coral, FL by replacing a malfunctioning circuit breaker responsible for intermittent power outages. Ensured a secure connection with a new breaker. Conducted a thorough inspection of the entire electrical panel to address potential hazards. The repair was done quickly and the client is very happy.

Completed a dishwasher repair in Cape Coral, FL. Diagnosed the issue, replaced a faulty pump, and conducted thorough testing to ensure optimal functionality. The appliance is now restored to efficient performance, providing the client with a reliable and fully operational dishwasher.

Went out to a customer's home to provide a whole house surge protection service. I assessed their electrical system and selected the right surge protection device to ensure proper coverage. The device was then carefully installed at the main electrical panel. The customer will now have a reliable electrical environment in their home.

Appliance repair for a residential customer. At their home, I inspected their kitchen refrigerator and found that the compressor was malfunctioning. The problematic component was removed and a new compressor was installed. The appliance is now running efficiently again for the home. The customer was thankful for the service.

Arrived at a residential home to provide whole house surge protection. Upon our arrival, we assessed the home's electrical system to determine the best placement for the surge protectors. We then carefully installed protection devices at key points throughout the home. The new devices will shield valuable devices in the home from any unexpected power surges.

Went out to a customer's home to replace their electrical panel. We had found corrosion and rust in the box on a previous visit so we quickly scheduled this service. The old panel was carefully disconnected and removed before the new panel was expertly installed. The power was then turned back on and the panel was tested to ensure it was working properly for the home. The customer was pleased with the service.

Installed new lights in a residential home. The customer had called us about updating the lighting in their kitchen. When I arrived, I carefully measured and marked the ideal positions for the lights before mounted the fixtures. Upon completion, I ensured that the lights were level and secure. The lights are working properly and the customer was pleased with the upgrade to their kitchen.

Arrived at a residential home to upgrade the customer's electric panel. I shut off the power supply and carefully removed the old panel before meticulously installing the new one. Upon completion, I turned the power back on to ensure the panel was working properly. The customer was pleased to have a more efficient electrical system.

Went out to a residential home to install new recessed lights in the home. The customer had recently bought the home and wanted to upgraded the lighting in their kitchen. Upon arrival, I measure the ceiling for spacing and placement. Once the wiring was complete and the lights were in place, I tested the lights to ensure they worked properly and that there were no issues with the wiring and the electrical system. The customer was happy with the upgrade.